Welcome to Lemmy Shitpost. Here you can shitpost to your hearts content.
Anything and everything goes. Memes, Jokes, Vents and Banter. Though we still have to comply with lemmy.world instance rules. So behave!
1. Be Respectful
Refrain from using harmful language pertaining to a protected characteristic: e.g. race, gender, sexuality, disability or religion.
Refrain from being argumentative when responding or commenting to posts/replies. Personal attacks are not welcome here.
...
2. No Illegal Content
Content that violates the law. Any post/comment found to be in breach of common law will be removed and given to the authorities if required.
That means:
-No promoting violence/threats against any individuals
-No CSA content or Revenge Porn
-No sharing private/personal information (Doxxing)
...
3. No Spam
Posting the same post, no matter the intent is against the rules.
-If you have posted content, please refrain from re-posting said content within this community.
-Do not spam posts with intent to harass, annoy, bully, advertise, scam or harm this community.
-No posting Scams/Advertisements/Phishing Links/IP Grabbers
-No Bots, Bots will be banned from the community.
...
4. No Porn/Explicit
Content
-Do not post explicit content. Lemmy.World is not the instance for NSFW content.
-Do not post Gore or Shock Content.
...
5. No Enciting Harassment,
Brigading, Doxxing or Witch Hunts
-Do not Brigade other Communities
-No calls to action against other communities/users within Lemmy or outside of Lemmy.
-No Witch Hunts against users/communities.
-No content that harasses members within or outside of the community.
...
6. NSFW should be behind NSFW tags.
-Content that is NSFW should be behind NSFW tags.
-Content that might be distressing should be kept behind NSFW tags.
...
If you see content that is a breach of the rules, please flag and report the comment and a moderator will take action where they can.
Also check out:
Partnered Communities:
1.Memes
10.LinuxMemes (Linux themed memes)
Reach out to
All communities included on the sidebar are to be made in compliance with the instance rules. Striker
My dad was a boomer, he insisted that Phillips heads didn't used to strip out this bad and it's just that everyone switched to making shit cheap screws out of shit cheap material. He also lived to see the enshittification of appliances from something you buy once in your life to something you buy every five years (at least, according to the warranty) with a nifty galifty payment plan. Walking into home Depot instantly radicalized him.
I think I'm with your boomer dad on that, though. Screws are increasingly cheaper and shoddier than they use to be, and probably because of the materials used are light and easy to produce. Now, the boomers blame "them dang cheap Chinese screws" but we all know it's enshittification for the sake of profit (which I guess can and would include globalization of supply chains).
True, but on the other hand, the drills or impact drivers are also getting stronger and stronger, so it's easier to mess up a screw. And then there's the driver bits, they're so bad these days that every new box of screws comes with a free bit.
I still hand screw things and they still break even with the right size driver, haha. But yes, those titanium coated bits make quick work of aluminum screws.
Your dad is right. I never used to strip out Robertson deck screws. Now, if you're lucky enough to get a screw in, the chances of getting it out unstripped approaches nil. If I search around and find good brands like Richileu, I don't have that problem. The shit Chinesium screws at Home Depot today are horrendous.
I'm not positive that this comment is Canadian enough.
He forgot to mention that after Home Depot, he stopped by Timmies on the way to his rec hockey game
i'd believe it to be honest, problem is phillips is still shit. You put ANY torque into them, you're gonna need to put a LOT of back pressure on them. Which is the primary reason they tend to strip anyway, inadequate back pressure, causing the bit to slip, getting a purchase on the fragile little corners, and then fucking DELETING them from existence.
I am old enough to remember when they only had manual screw drivers and thicker wood screws that needed to be pre-drilled and lubed with soap.
Go buy a modern "cheap" wood screw. Not a deck screw. An actual wood screw. Pre-drill the correct size hole, including the countersink, and use the correct size manual Phillips screwdriver. You will never strip out the screws.
Now take a 500 RPM impact driver that has almost enough torque to remove lug nuts, a worn or wrong size bit, and a thin shank screw that was only designed to hold down deck boards and the slightest slip or misalignment and have this photo.
We all do it because it is fast/easy. Just understand that you are doing things the convenient way instead of the right way, and you have to expect the stuff to sometimes not work aa advertised because of it.
I'm a millennial, I don't really recall phillips screws getting universally worse over my lifetime. I've torn the drive out of a LOT of them over the last three decades.
What I have seen is Phillips holding still while the rest of screwology improves around them. Take an impact driver and blast in a few 3.5" #10 Torx deck screws, then try to install a Phillips head screw and see if you can keep the word "bullshit" from coming out of your mouth.
There's also the issues of Pozidriv and JIS, which both superficially resemble Phillips but are different and work VERY poorly if turned with a Phillips driver.
Home appliance enshittification is real though. I'm running my Kenmore 80 series for as long as I can.
Millennial here, too. Phillips screws have been made of fucking cobwebs and wet tissue as far as I remember too.
total torx supremacy
Torx gang reporting in 👌👍
Snap the bolt before you ever strip the screw. I hate regular alan keys, torx should be the default everywhere. I did lose too many torx bits when impacting though
I'm actually conflicted; I have a lot more trouble with torx at work than I do alan, but phillips are universally a problem. The torx keys don't stick in the hole and can't be tilted at odd angles where as alan keys with a ball head can, and do stick in the hole to some degree which lets me free-spin it if I have clearance. I've ruined a lot more torx from over-torgue than I have alan keys. I would take torx over alan keys if it meant I never had to see a phillips again, though
One of the IT guys at my work is really good at stripping torx, but that's because he uses a driver a couple sizes too small.
That's just... Wow.
Oh, the heads not quite flush, lemme give it juuuuuuust a bit moreahhhhfuck
Maybe if I just stop, align it perfectly, put more pressure behind it and gently start tuuuAHHHFUCKOFF!!!!
+1 for torx being available in america. +1 for robertson existing at all.
pozidriv is pretty cool, but annoying to use since people confuse it with phillips all the time so you end up with a lot of stripped screws.
torx is the way to go. their sizing is odd, but it transfers torque well and is wear-resistant.
"It's a Pozidrive bro, you can't- you can't just use a... annnnd you stripped it"
Partially stripped phillips? Grab a flathead screwdriver close to the same size and use a hammer to tap it down into the screw head. Twist it out while pushing down.
Get yourself some real screws get yourself roberston
Canadian invented square Robertson screws are the best.
I wish that were the case, but most store brands have enshittified to be made out of cottage cheese. Even robertsons have this issue now if you don't search around for good brands. Generic trash is trash.
I'm in the process of rebuilding a house and a new shop, and the last time I did this, it was nowhere near as big of a problem.
I'm a screw stripper
How do I tag a comment nsfw
If it's wrong to be turned on by the sound of a DeWalt cordless drill, then I don't wanna be right.
Here's a tip for anyone with this problem. Take an elastic band and place it over the devastated screw and try again.
I've tried this hundreds of times and it's never worked.
Of course not. But it's funny to watch you try.
I posted it above, but the best way is to Dremel with a metal cutting blade to convert it to a flat head.
Source: I used to work for Home Depot and had to fix shit for people all the time.
skill issue
